Pressure Treated Wood: Types, Grading Standards & More | (2024)

What is Pressure Treated Wood?

Pressure treated wood is lumber impregnated with a variety of preservative chemicals to prevent rot and insect infestation in exterior applications like decks and fences. Several species of wood can be treated, but a regionally available species usually predominates in any particular locale.Pressure treated lumber is ideal for outdoor construction as it has a long, useful life span and is much less expensive than alternatives.

How is Lumber Pressure Treated?

The treatment process involves placing a load of lumber in a huge cylindrical chamber called a retort with a door on one end that can be sealed airtight, and then forcing waterborne chemicals into the wood under pressure. The preservative chemicals are forced deep into the cellular structure of the wood and become part of the wood just as you see a colored transparent stain soak into and become part of the wood trim inside a home.

Once the raw wood is loaded into the cylindrical retort, a powerful vacuum is applied pulling the air out of the lumber and the retort. The retort is then flooded with the preservative chemicals and they’re drawn deep into the lumber like a magnet is attracted to iron. It’s not uncommon to raise the pressure inside the retort to over 150 pounds per square inch to drive the chemicals into the lumber.

After the chemical has been pushed into the lumber, it’s removed from the retort and set on a drip pad to capture the chemical preservative that leaks out of the lumber. This liquid is recycled and reused in the next batch. The lumber can’t be sold until all the excess chemical drips out. This may only take a few days in hot summer weather, but it can extend to two weeks in damp, cold winter weather.

How Long Does Pressure Treated Wood Last?

Treated wood can last more than 40 years. However, there are countless stories and photographs on the Internet showing failure of treated lumber in fewer than ten years. Treated lumber rated for ground contact can be partially destroyed by termites in less than five years.

There are many factors that weigh into why some treated lumber lasts longer than pieces that fail. It’s a good idea for you to keep the treated lumber around your house sealed as best as possible to prevent water from entering the wood, especially the end grain. Water fuels wood rot. Keep wood dry and it will not rot. It’s that simple.

If you need to bury treated lumber as you build a deck, playset, or outdoor shed, it’s a very good idea to surround the treated lumber posts with sand. You can purchase DIY termite treatment chemicals from many retailers. Mix up the solution as stated on the label and saturate the sand every few years as a preventative measure to keep termites away from the lumber.

Is Pressure Treated Wood Stronger?

The strength and properties of lumber from different species of wood varies considerably. Species like southern pine and Douglas fir are often used for deck framing. Both of these species are very strong. That said, strength varies according to the grade of the lumber. The strongest is Select, which is usually free of any knots. Number One grade is the next strongest. The higher the grade number the less strength it contains as knots in lumber are places where failure or cracks typically develop.

There are a handful of species commonly used for structural framing, and while relatively similar, their properties affect how far they can span as joists. Span tables will list species separately for this reason.

Types of Pressure Treated Wood

There are two primary types of pressure treated wood. The most common one you see in lumber yards and home centers is the type treated with water-based chemicals. Industrial and commercial customers such as electric utilities and railroads will purchase the second type of treated lumber that contains oil-based preservatives. You’ve likely noticed how electric poles and railroad ties under the steel rails look much different than the treated lumber that’s on your deck.

When it comes to treated lumber intended for use around the home, you’ll quickly discover when you read the print on the tag on the end of each piece how it’s supposed to be used.

  • Above Ground Use - this type should never contact the soil. UC2 classification is for interior use in damp locations. UC3 classification is for above ground exterior construction. UC3A is for coated treated lumber with rapid water runoff. UC4A is for use in uncoated situations with poor water runoff.
  • Ground Contact - this type is made for ground contact. UC4 classification is for treated wood exposed to fresh water environments. UC4A is for general use. UC4B is for heavy-duty use.

There are many different chemicals used to treat lumber to prevent decay and to inhibit destruction by wood-boring insects. Here are a few common ones. Note that the more chemical that’s injected into the wood, the higher the protection. This weight is usually printed on the tagstapled to the end of each piece of treated wood. This is typically expressed on a label as pounds of preservative chemical per cubic foot of wood:

  • ACQ - Alkaline Copper Quaternary (Type B or C)
  • ACQ - Alkaline Copper Quaternary (Type A or D)
  • CA-B - Copper Azole, Type B
  • CA-C - Copper Azole, Type C
  • Cu N-W - Waterborne Copper Naphthenate

Pressure Treated Lumber Grading Standards

Grade is a description of the quality of a given species. As lumber moves through a mill, grading inspectors review each piece and separate them onto different paths. Knots, decay, grain angle, wane, damage, warp and other physical characteristics of an individual piece of lumber distinguish it into a specific grade.

The grades provide a tighter presumption of the structural performance of each piece. A beat-up, decayed 2x8 covered in knots won’t be as strong as a clean, straight-grained one. Common grades, from worst to best, are utility and structural select. Span tables will also list grades in separate columns to further fine-tune the maximum allowable span.

Because treated wood is often still wet when it is delivered to the site, it will shrink slightly in width and thickness as it dries out. This can cause significant twisting, cupping, bowing and warping especially in lower-grade boards where knots and uneven grains are already present. It is possible that some boards will become so deformed that they will be unusable. You may want to store lumber by fastening boards together using a method called stickering to allow boards to dry evenly. You may also purchase kiln-dried after treatment (KDAT), which is much more stable, but also more expensive.

  • Premium - Highest grade for ¾ radius edge decking.
  • Select - The highest grade available, contains very few defects. It must meet a minimum 1/12-grain slope and have all knots sound encased. It has a high consistency and the appearance is very good.
  • Number 1- Will contain no splits larger than the width of the board. Knots may not be larger than 2 ¾". One hole is permitted every 3 ft.
  • Standard - Mid-range grade for 5/4 decking.
  • Number 2 - Grain slope must meet minimum 1/8 grain slope. Boards will contain no splits larger than 1.5 times width of board. Knots may not be larger than 3 ½". One hole is permitted every 2 ft. Wane corners.
  • Number 3 - The lowest-quality grade. Not suitable for deck construction.

Species & Sizes Of Pressure Treated Wood

Treated wood is generally available as dimensional stock in 2x4s, 2x6s, 4x4s and 2x2s for rail components. 5/4x6s and 2x6s for decking. 2x8s, 2x10s and 2x12s for joists, stair stringers and beams. 6x6s for support posts and plywood.

The predominant species of treated wood is a regionally available softwood.Most common are:

  • Southern Yellow Pine - Southern pine is the most common deck framing material in the eastern United States. It is strong and stiff. SYP logs yield a high proportion of sapwood, which works well to absorb preservative.
  • Red and Ponderosa Pine - Less strong than SYP, found in northern U.S. and Canada.
  • Douglas Fir – It is very strong and is less prone to warping and spitting than SYP. Predominant material found in western U.S. and Canada.
  • Hem-Fir – It is weaker and more prone to warping and splitting than Douglas fir, but more receptive to preservation. It encompasses a group of western species.

Uses for Pressure Treated Wood

Different applications impose different hazards on wood, and require different amounts of preservative for protection. These amounts are called “retention levels,” referring to the amount of preservative retained in the wood after treatment. Furthermore, each preservative has its individual retention level for these applications. Be sure to obtain wood treated for the application you have in mind. The intended use is identified on the tag stapled to each piece of lumber.

From a homeowner’s perspective, you’d use pressure treated lumber in any situation where it’s likely the wood could get wet. Water is the enemy of wood as it provides the needed moisture that wood-destroying fungus requires to thrive and consume the wood.

You’d also use treated lumber in any building environment where wood-destroying insects are in abundance. It’s very common in tropical climates to use treated lumber for all the framing lumber in a house.

Cost of Pressure Treated Wood

Supply and demand for building products can create unexpected cost increases. The cost of pressure treated wood is not immune from this economic reality. It’s often hard to predict rapid price increases. Labor shortages, supply-chain issues for preservative chemicals, transportation bottlenecks, etc., can all contribute to price increases. Price decreases happen, but they tend to be a much slower process as the retailers have to bleed off their higher-priced inventories.

If you’re worried about the price of treated lumber, you may want to look at the prices of composite decking. You can’t use composite lumber for the structural undercarriage of your deck, but it can be used for the decking and railing system. In certain instances, it might be a less-expensive alternative.

Ready to get started with your pressure treated wood project? Find a builder or retailer near you.

Pressure Treated Wood: Types, Grading Standards & More | (2024)


What are the grades of pressure treated deck boards? ›

Pressure treated wood is sold with the lumber grades Premium, Select, Number 1, Number 2, and Number 3. The higher the grade, the fewer the defects—that is splits or knots. In general, you will want to choose Number 2 grade boards, or higher, for decks.

What is the best pressure-treated wood to use for a deck? ›

Pressure Treated Wood

There are a few different types of wood that are commonly pressure treated for decks, but the two most popular are southern yellow pine and douglas fir.

What is the difference between #1 and #2 grade treated lumber? ›

Typically wood that is two or more inches thick is graded only for strength, denoted by #1, #2 and so on. And because stronger lumber has fewer and smaller knots, it's typically more attractive. So the general rule of thumb for lumber grades is this: the lower the number, the more strength and better appearance.

What is the difference between standard and premium pressure treated decking? ›

There are two grades for Radius Edge Decking - Standard and Premium. Standard 5/4" Radius Edge Decking will have large knots, and very limited bark and wane. Premium 5/4" will be just below a "D" grade, and be mostly clear with a few small dime and quarter-sized knots per board. It will have no bark and wane.

What is the difference between ACQ and CCA treated wood? ›

ACQ (alkaline copper quaternary) – Contains a quaternary compound including copper and ammonium. ACQ is strong against fungi, insects, and other marine creatures that may damage the integrity of lumber. CCA (chromated copper arsenate) – A combination of chromium, copper, and arsenic for maximum protection.

What is the difference between MCA and CCA treated wood? ›

It includes copper and two types of azole. CA-C was approved in 2009 and is currently the industry standard. One increasingly common form of CA-C is Micronized Copper Azole (MCA). The primary difference of MCA compared to CA is that the copper in the CA solution chemically bonds to the wood.

What is the longest lasting pressure-treated wood? ›

Pine, cedar, Douglas fir, and hem-fir are the species that best absorb the pressure-treatment chemicals, making them ideal for long-lasting woodwork. Pine and cedar are the most commonly used types of wood for deck framing.

What is number 1 pressure-treated lumber? ›

Number one grade pressure-treated lumber may have an irregular grain pattern and will often contain small knots or knot holes along the edge. Number one grade pressure treated lumber may have also been treated with water sealer or kiln dried, but not always.

Is it better to stain or paint pressure-treated wood deck? ›

How to Stain Pressure-Treated Lumber. Stain is usually the preferred way to finish pressure-treated lumber because it soaks better into the wood and is easier to apply than paint is.

What are the three categories of treated lumber? ›

The three main families of treated lumber used in construction. Borate, Alkaline Copper Quat (ACQ) and other rot-resistant treatments, and non-combustible (Non-Com).

What are the 5 lumber grades? ›

Table 2: Lumber Grades for Common (nonstress-graded) Lumber
GradeDesignationTypical Uses
No. 2StandardSimilar uses to No. 1
No. 3UtilitySheathing, subflooring, crate construction
No. 4EconomySheathing, subflooring, creation of forms for concrete work
No. 5EconomySimilar uses to No. 4
1 more row
Dec 1, 2023

What is the strongest treated lumber? ›

CCA treated wood is still considered by many construction professionals to be the best wood treatment option. It is ideal for outdoor projects that require a high level of durability and resistance to the elements.

What grade of pressure treated wood for decks? ›

Premium - Highest grade for ¾ radius edge decking. Select - The highest grade available, contains very few defects. It must meet a minimum 1/12-grain slope and have all knots sound encased. It has a high consistency and the appearance is very good.

What is the best decking for longevity? ›

In comparison to wood, PVC, aluminium, and steel, composite decking is the longest-lasting material for your deck. Its overall longevity, aesthetic qualities, and low maintenance make it the most desirable material to use.

Is IPE decking worth the cost? ›

One common concern about Ipe decking is its cost. While Ipe wood may have a higher initial price compared to other decking materials, it offers superior quality and performance. In fact, real Ipe wood is currently priced lower than synthetic decking options and outperforms them!

Are there different grades of decking? ›

Deck boards are a key structural part of the deck, and they should always be graded - this helps to ensure strength and durability and could also lead to cost savings on the sub-structure. The most common timber grades for softwood deck boards are C16 and C24.

What do the numbers mean on pressure-treated wood? ›

A-The numbers on pressure-treated wood refer to the levels of preservative treatment and are important because they designate the intended uses of the wood. The numbers commonly used are LP-2, LP-22, 0.25 and 0.40.

What does #2 prime lumber mean? ›

Prime Grade Lumber:

Use when appearance is important. Prime grade lumber provides the same structural properties as #1 grade lumber, but has fewer knots and better appearance. #2 Prime grade has the strength of #2 grade lumber, but will look better, with fewer knots.

Top Articles
Latest Posts
Article information

Author: Arielle Torp

Last Updated:

Views: 5947

Rating: 4 / 5 (41 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Arielle Torp

Birthday: 1997-09-20

Address: 87313 Erdman Vista, North Dustinborough, WA 37563

Phone: +97216742823598

Job: Central Technology Officer

Hobby: Taekwondo, Macrame, Foreign language learning, Kite flying, Cooking, Skiing, Computer programming

Introduction: My name is Arielle Torp, I am a comfortable, kind, zealous, lovely, jolly, colorful, adventurous person who loves writing and wants to share my knowledge and understanding with you.